Routed 50 x 20 mm two-layer KiCad PCB with 3D renders
GPT-6 Astra took a schematic PDF through KiCad to a revised circuit and a routed two-layer board with zero DRC violations, plus 3D renders.

Buat model 3D yang detail
Kode saja hanya menghasilkan bentuk sederhana. Wandy 2 mengubah satu foto menjadi model 3D bertekstur yang bisa Anda pakai di adegan yang sama.
Panduan build dari Wandy3D
Penulis tidak membagikan prompt-nya, jadi kami menuliskan cara membuat ulang karya ini.
Build a small sensor-board design project in KiCad starting from a supplied schematic PDF. Redraw the schematic so it follows the PDF's layout and style, change only the sensor-interface section the user specifies, and keep every other part and connection unchanged. Review component datasheets and run the electrical rules check. Then lay out and route a 50 x 20 mm two-layer PCB with four corner mounting holes, a four-pin connector on one short edge, a microcontroller, a few small ICs, a boot button and labelled test pads. Use a dark green solder mask with silk-screen labels. Finish by running the design rule check until it reports zero violations, and export a 3D board render plus front and mirrored back layout views. Deliver the KiCad project, the schematic PDF and the renders, with a short note listing unresolved checks and the fact that hardware testing has not yet been done.
Cara memakai prompt ini
Give the build brief to GPT-6 Astra in an agent that can drive KiCad, along with your own schematic PDF.
Change the sensor section, board size, connector and mounting holes to match your hardware, and keep the rest fixed.
You get a schematic, a routed board and 3D renders; re-run ERC and DRC, then ask for datasheet checks before ordering.
Dari Wandy3D
Butuh model 3D sungguhan di adegan Anda?
Agen Anda membangun dengan bentuk primitif. API Wandy3D mengubah foto atau prompt menjadi GLB bertekstur dalam beberapa menit — dibayar dari saldo prabayar, tanpa langganan.
- Wandy 2US$0,18 per model
- Wandy 1US$0,09 per model
Saldo tidak pernah kedaluwarsa · tugas yang gagal dikembalikan · model yang dibuat lewat API milik Anda dan bisa diunduh dalam semua format.
curl -s -X POST https://api.wandy3d.com/generate/cloud/ultra \ -H "Authorization: Bearer $WANDY3D_API_KEY" -F "file=@photo.jpg"# → {"task_id": "…"} — poll until "status" is "done":curl -s https://api.wandy3d.com/task/$TASK_ID/status \ -H "Authorization: Bearer $WANDY3D_API_KEY"# → {"model_id": "…"} — then GET /model/$MODEL_ID/export?format=glbPostingan asliAnda penulisnya? Minta kami mengedit atau menghapus halaman ini
Prompt serupa
Lihat semua prompt
GPT-6 AstraGolden tilt-shift pyramid diorama that builds itself, two-model comparison
demon
GPT-6 AstraIsaac Sim carpentry workbench scene for robot manipulation testing
Charles Wong
GPT-6 AstraGolden Gate Bridge in morning fog, low-angle Blender-style render
EvoLink.ai
GPT-6 AstraLow-poly open-world adventure with a built-in terrain editor
ふぐあい(ふぐおん)
GPT-6 AstraInteractive 3D camera lens demo with light rays over a mountain valley
noah helms
GPT-6 Astra3D lake village scene with an island house, bridge and flowered paths
Givros




