Routed 50 x 20 mm two-layer KiCad PCB with 3D renders
GPT-6 Astra took a schematic PDF through KiCad to a revised circuit and a routed two-layer board with zero DRC violations, plus 3D renders.

Tạo mô hình 3D chi tiết
Chỉ dùng code thì chỉ được các hình khối đơn giản. Wandy 2 biến một tấm ảnh thành mô hình 3D có texture để bạn dùng ngay trong cùng cảnh đó.
Hướng dẫn dựng từ Wandy3D
Tác giả không chia sẻ prompt, nên chúng tôi đã ghi lại cách tái tạo sản phẩm này.
Build a small sensor-board design project in KiCad starting from a supplied schematic PDF. Redraw the schematic so it follows the PDF's layout and style, change only the sensor-interface section the user specifies, and keep every other part and connection unchanged. Review component datasheets and run the electrical rules check. Then lay out and route a 50 x 20 mm two-layer PCB with four corner mounting holes, a four-pin connector on one short edge, a microcontroller, a few small ICs, a boot button and labelled test pads. Use a dark green solder mask with silk-screen labels. Finish by running the design rule check until it reports zero violations, and export a 3D board render plus front and mirrored back layout views. Deliver the KiCad project, the schematic PDF and the renders, with a short note listing unresolved checks and the fact that hardware testing has not yet been done.
Cách dùng prompt này
Give the build brief to GPT-6 Astra in an agent that can drive KiCad, along with your own schematic PDF.
Change the sensor section, board size, connector and mounting holes to match your hardware, and keep the rest fixed.
You get a schematic, a routed board and 3D renders; re-run ERC and DRC, then ask for datasheet checks before ordering.
Từ Wandy3D
Cần một mô hình 3D thật trong cảnh của bạn?
Agent của bạn dựng cảnh bằng các khối cơ bản. API Wandy3D biến ảnh hoặc prompt thành tệp GLB có texture chỉ trong vài phút — trả từ số dư nạp trước, không cần đăng ký gói.
- Wandy 20,18 US$ mỗi mô hình
- Wandy 10,09 US$ mỗi mô hình
Số dư không bao giờ hết hạn · tác vụ lỗi được hoàn tiền · mô hình tạo qua API thuộc về bạn và tải xuống được ở mọi định dạng.
curl -s -X POST https://api.wandy3d.com/generate/cloud/ultra \ -H "Authorization: Bearer $WANDY3D_API_KEY" -F "file=@photo.jpg"# → {"task_id": "…"} — poll until "status" is "done":curl -s https://api.wandy3d.com/task/$TASK_ID/status \ -H "Authorization: Bearer $WANDY3D_API_KEY"# → {"model_id": "…"} — then GET /model/$MODEL_ID/export?format=glbBài đăng gốcBạn là tác giả? Yêu cầu chúng tôi sửa hoặc gỡ trang này
Prompt tương tự
Xem tất cả prompt
GPT-6 AstraGolden tilt-shift pyramid diorama that builds itself, two-model comparison
demon
GPT-6 AstraIsaac Sim carpentry workbench scene for robot manipulation testing
Charles Wong
GPT-6 AstraGolden Gate Bridge in morning fog, low-angle Blender-style render
EvoLink.ai
GPT-6 AstraLow-poly open-world adventure with a built-in terrain editor
ふぐあい(ふぐおん)
GPT-6 AstraInteractive 3D camera lens demo with light rays over a mountain valley
noah helms
GPT-6 Astra3D lake village scene with an island house, bridge and flowered paths
Givros




